PA66 103HSL NC010ÃÀ¹ú¶Å°îZytel® ÈÈÎȶ¨È󻬾Ûõ£°·66ÄáÁúËÜÁÏ×¢ËܳÉÐÍ£¨18024445500£©
Zytel® 103HSL NC010 is a heat stabilised, lubricated polyamide 66 resin for injection moulding.
General information Value Unit Test Standard
Resin Identification PA66 - -
Part Marking Code >PA66< - ISO 11469
RheologicalViscosity numberproperties 136dry[1]/ cond/* Unitcm&sup3;/g TestISO 307,Standard1157, 1628
Moulding shrinkage, parallel 1.3 / * % ISO 294-4, 2577
Moulding shrinkage, normal 1.3 / * % ISO 294-4, 2577
1: formic acid 90% ¡¡ ¡¡ ¡¡
Mechanical properties dry/cond Unit Test Standard
Tensile Modulus 3100/1400 MPa ISO 527-1/-2
Yield stress 85/58 MPa ISO 527-1/-2
Yield strain 4.5/25 % ISO 527-1/-2
Nominal strain at break 20/>50 % ISO 527-1/-2
Strain at Break, 23¡ãC, 50mm/min 40/- % ISO 527-1/-2
Flexural Modulus 2800/1200 MPa ISO 178
Tensile creep modulus ¡¡ ¡¡ ISO 899-1
1h * / 1190 MPa ¡¡
1000h * / 540 MPa ¡¡
Charpy impact strength ¡¡ ¡¡ ISO 179/1eU
23¡ãC N / N kJ/m&sup2; ¡¡
-30¡ãC 400 / N kJ/m&sup2; ¡¡
Charpy notched impact strength ¡¡ ¡¡ ISO 179/1eA
23¡ãC 5.5 / 12 kJ/m&sup2; ¡¡
-30¡ãC 4.5 / 3.5 kJ/m&sup2; ¡¡
Izod notched impact strength ¡¡ ¡¡ ISO 180/1A
23¡ãC 5 / 10 kJ/m&sup2; ¡¡
-30¡ãC 6 / 5 kJ/m&sup2; ¡¡
-40¡ãC 5.5 / - kJ/m&sup2; ¡¡
Izod impact strength ¡¡ ¡¡ ISO 180/1U
23¡ãC N/N kJ/m&sup2; ¡¡
-30¡ãC 300/N kJ/m&sup2; ¡¡
Thermal properties dry/cond Unit Test Standard
Melting temperature, 10¡ãC/min 262/* ¡ãC ISO 11357-1/-3
Glass transition temperature, 10¡ãC/min 60/- ¡ãC ISO 11357-1/-2
Temp. of deflection under load ¡¡ ¡¡ ISO 75-1/-2
1.8 MPa 70 / * ¡ãC ¡¡
0.45 MPa 200 / * ¡ãC ¡¡
Vicat softening temperature, 50¡ãC/h, 50N 240 / * ¡ãC ISO 306
Coeff. of linear therm. expansion, parallel 100 / * E-6/K ISO 11359-1/-2
Coeff. of linear therm. expansion, normal 110 / * E-6/K ISO 11359-1/-2
Thermal conductivity of melt 0.16 W/(m K) -
Spec. heat capacity of melt 2790 J/(kg K) -
Eff. thermal diffusivity 5E-8 m&sup2;/s -
RTI, electrical ¡¡ ¡¡ UL 746B
0.75 mm 140 / * ¡ãC ¡¡
1.5mm 140 / * ¡ãC ¡¡
RTI, impact ¡¡ ¡¡ UL 746B
0.75 mm 95 ¡ãC ¡¡
1.5mm 110 / * ¡ãC ¡¡
RTI, strength ¡¡ ¡¡ UL 746B
0.75 mm 115 ¡ãC ¡¡
1.5mm 125 / * ¡ãC ¡¡
Flammability dry / cond Unit Test Standard
Burning Behav. at 1.5mm nom. thickn. V-2 / * class IEC 60695-11-10
Thickness tested 1.5 / * mm IEC 60695-11-10
UL recognition UL / * - -
Burning Behav. at thickness h V-2 / * class IEC 60695-11-10
Thickness tested 0.71 / * mm IEC 60695-11-10
Oxygen index 28 / * % ISO 4589-1/-2
Glow Wire Flammability Index ¡¡ ¡¡ IEC 60695-2-1/2
0.75mm 850 / - ¡ãC ¡¡
1.5mm 960 / - ¡ãC ¡¡
3mm 960 / - ¡ãC ¡¡
Glow Wire Ignition Temperature ¡¡ ¡¡ IEC 60695-2-1/3
0.75mm 725/- ¡ãC ¡¡
1.5mm 725/- ¡ãC ¡¡
3mm 725/- ¡ãC ¡¡
Electrical properties dry/cond Unit Test Standard
Relative permittivity ¡¡ ¡¡ IEC 60250
100Hz 3.8 / 12.8 - ¡¡
1MHz 3.5 / 4 - ¡¡
Dissipation factor ¡¡ ¡¡ IEC 60250
100Hz 75/5800 E-4 ¡¡
1MHz 165/700 E-4 ¡¡
Volume resistivity 1E13/1E11 Ohm*m IEC 60093
Electric strength 31/28 kV/mm IEC 60243-1
Comparative tracking index ¡¡ ¡¡ ¡¡
Comparative tracking index 600 / - - IEC 60112
3.0mm 0 / - PLC UL 746A
Dielectric Constant ¡¡ ¡¡ ASTM D 150
1 MHz 3.5 / - - ¡¡
100 Hz 3.6 / - - ¡¡
Surface Resistivity 1E12 / - Ohm ASTM D 257
Other properties dry / cond Unit Test Standard
Humidity absorption, 2mm 2.6 / * % Sim. to ISO 62
Water absorption, 2mm 8.5 / * % Sim. to ISO 62
Density 1140 / - kg/m&sup3; ISO 1183
Density of melt 980 kg/m&sup3; -
Film Properties dry / cond Unit Test Standard
Strain at yield, parallel 4.5 / * % ISO 527-3
VDA Properties Value Unit Test Standard
Emission of organic compounds 2.1 &micro;gC/g VDA 277
Odour 2.5 class VDA 270 |