常州修理厂地坪*** 400-0709-910(请拨打400-0709-910电话，永坚地坪公司)

车间内的环氧地坪上行车要注意速度不可过快，以免争刹车行为造成剪切发热过高，从而使得环氧地坪漆瞬间软化（环氧地坪漆的软化温度在80℃左右，因此其使用环境温度一般控制在50℃以下）并在剪切力的作用下产生难以清洗的污痕

常州修理厂地坪*** 400-0709-910(请拨打400-0709-910电话，永坚地坪公司)

养护介绍
1、建议行人穿软底鞋（若现场条件允许），进入工业地坪区前要清理干净鞋底上的砂粒等硬质物，以减少锐利物体对地坪表面的划伤。
2、搬运物品尽量做到轻举轻放，防止重物冲击地面，以免造成人为损坏。
3、车间内的环氧地坪上行车要注意速度不可过快，以免争刹车行为造成剪切发热过高，从而使得环氧地坪漆瞬间软化（环氧地坪漆的软化温度在80℃左右，因此其使用环境温度一般控制在50℃以下）并在剪切力的作用下产生难以清洗的污痕。

常州修理厂地坪*** 400-0709-910(请拨打400-0709-910电话，永坚地坪公司)

4、日常清洁可用地坪清洗机或湿抹布擦试，可选用中性清洁剂清洗，也可使用一般洗涤剂以较小浓度加入水中做成清洗液，然后使用地坪清洗机或棉布拖把洗净地坪表面的污渍，并用清水再洗一遍，擦干地面；注意地坪漆边缘部分不要较长时间有积水。
5、不定期进行打蜡处理（一般每个月要打蜡一次），建议使用专用地板蜡或乳化水性蜡；先使用地坪清洗机或棉布拖把将地坪清洗干净并拭干，然后打蜡处理。打蜡处理可以增加任何地坪材料的耐磨性及抗划伤性.

常州修理厂地坪*** 400-0709-910(请拨打400-0709-910电话，永坚地坪公司)

6、避免使用重物或是工具敲击地面，也不可直接在环氧地面上拖移重物。
7、避免重腐蚀性介质长时间浸泡地坪漆膜，如不慎重腐蚀性酸碱洒落，请务必及时清理干净酸碱介质。

、施工注意事项

常州修理厂地坪*** 400-0709-910(请拨打400-0709-910电话，永坚地坪公司)

1、基础地面打磨、修补、清理后的基础地面强度在达C25以上，平整度2-3mm/2M以内，地面无油污，其他化学物品残留。
2、涂布完每道涂层后注意检测表面情况，有没有弊病产生，每施工一道涂层不易过厚，施工力度在均匀，一定要完全固化后，才可以进入下道工序。
3、必需地坪漆材料标准比例配比，充分搅拌均匀。


Driving to pay attention to the workshop on epoxy floor speed can not too fast, so as not to compete brake behavior caused shearing heat is too high, so that the epoxy floor paint instantly softened (epoxy floor paint softening temperature around 80 ℃, Therefore, the use of ambient temperature is generally controlled at below 50 ℃) and produces difficult to clean dirty under shear stress

Changzhou repair shop floor Which 400-0709-910 (please call 400-0709-910 phone, Wing-kin flooring company)

Conservation Introduction
1, the proposed pedestrian wear soft-soled shoes (if field conditions allow), into the industrial floor area to be cleaned before the grit and clean the soles hard object, in order to reduce sharp objects on the floor surface scratches.
2, try to make light move moving objects gently to prevent heavy impact the ground, in order to avoid man-made damage.
3, driving the epoxy floor in the workshop should pay attention to the speed not too fast, so as not to compete brake behavior caused shearing heat is too high, so that the epoxy floor paint instantly soften (softening temperature epoxy floor paint at 80 ℃ so, so the use of ambient temperature is generally controlled at below 50 ℃) and produces difficult to clean dirty under the action of shear forces.

Changzhou repair shop floor Which 400-0709-910 (please call 400-0709-910 phone, Wing-kin flooring company)

4, available daily cleaning floor cleaning machines or wipe a wet rag, you can choose a neutral detergent, detergent can also be used in smaller concentrations are generally added to water to make a cleaning solution, and then use the floor cleaning machine or cotton swab wash net floor surface stains and wash again with clean water, dry ground; note floor paint edge portion do not have water for a long time.
5, irregular waxing (generally waxing once a month), we recommend using a dedicated floor wax or emulsified aqueous wax; first use of floor cleaning machines or cotton swab to clean and wipe the floor, then waxing deal with. Waxing can add any flooring materials wear resistance and scratch resistance.

Changzhou repair shop floor Which 400-0709-910 (please call 400-0709-910 phone, Wing-kin flooring company)

6, avoid using heavy tools or tap the ground, nor directly over epoxy floor drag heavy loads.
7, to avoid heavy corrosive medium long soak floor paint, corrosive acid spilled if not careful, please be sure to promptly clean up acid medium.

Construction Notes

Changzhou repair shop floor Which 400-0709-910 (please call 400-0709-910 phone, Wing-kin flooring company)

1, basic ground polish, repair, cleaning up after the basis of the ground strength of C25 in the above, the flatness within 2-3mm / 2M, ground no oil, other chemicals residues.
2, note that each coat finish is applied to detect surface conditions, there is no ills generated every construction is not easy too thick a coating, construction efforts in uniform, after must be completely cured before they can enter the next process.
3, the required floor paint material standard proportioning stir.

资讯来源：<联系电话:400-0709-910>