无锡糖果厂地坪价格是多少400-0709-910(请拨打400-0709-910电话，永坚地坪公司)

耐磨地坪漆施工中,*常见涂膜干燥方式是自然干燥,也可以成为常温干燥.但是这种干燥方法时间较长,而且受自然影响较严重.而且在环氧地坪漆的涂装后,涂膜越厚,完全干燥的时间就越长.
在涂膜的自然干燥过程中要注意以下几点:
1、环境的湿度对干燥的速度和涂膜的质量会有很大的影响.湿度高的情况下,可能会早场涂膜泛白.还可能会造成涂膜回粘,因此,**是湿度要小于75%.在通风的环境下,涂膜更容易干燥.但是风速不宜太大,否则会影响涂膜的质量.
2、气温太低或者是太高都会影响成膜的质量,所以应选择适宜的天气施工.光照对常温干燥也有很大的帮助,紫外线的光对聚合有明显作用,但也可能对涂膜造成伤害,要把握好度很重要.
把握好涂膜的干燥在整个停车场由于需要规划停车位置，同时还要安装相应的防护装置，因此需要提供各种不同颜色，不同规格的停车场地板漆来做好相应的规划，也因此而增加了施工的难度，在整个停车场的施工，每一个部分都需要精心的设计和规划，从而更加**的给予驾驶者一定的指示，既然停车场需要规划不同的颜色，那么我们该如何去设计才能够更好的利用整个停车场呢？小编拥有如下建议。
1、停车区对于平整地面,可采用0.5mm普通环氧地坪，而平整度及表面强度较差的地面，可以采用1-3 mm环氧砂浆地坪，**要求可采用2-3mm环氧自流平地坪；颜色可设计成灰色。
2、车行通道由于车行频繁，相对于停车区，设计要加强，可采用1-3 mm环氧砂浆地坪或2-3mm环氧自流平地坪，颜色通常为绿色，车行通道宽度根据现场情况设置，通常双向行车道不宜低于6米，单向行车道不宜低于3米，人行通道为1.5-2米，通道两侧划中黄色标志线，线宽8-12mm。
3、车行标志通道内可采用黄色或白色标志漆（可采用夜发花地坪漆）画箭头进行标明车行方向及指向各停车区，如A停车区、B停车区及C停车区等。
4、停车位设置按停车场地面区域结构设置停车位，小轿车通常可设计为2.5-3.0米X5-6米，停车位采用黄色或白色标志线画出，标线宽8-12mm。
5、柱面处理为增加停车场柱面的醒目性，避免因倒车碰到柱子，柱子下端1.0-1.2米以下可采用黄色和白色相间斜纹斑马线进行标明。
6、车辆出入口坡道无震动防滑地坪，车辆出入品必须具有防滑**噪音作用，有的停车场土建施工时已考虑到了，将之施工成波纹形不平的地面，这种情况下只需一部分涂车行通道颜色，一部分涂另一颜色，两种颜色相间就可以了。如果土建时未设计考虑防滑要求，在地坪施工明此处应采用AKF防滑地坪，而且防滑骨料颗径应较大，通常直径不低于2mm，视坡道倾斜度而选择合适颗径的防滑骨料。
7、墙裙处理墙裙涂以和墙面及地面不一样的颜色，可在车行时起到提醒的作用。但不宜过高，一般0.2-0.7米即可。采用深绿色和Wear-resistant floor paint construction, coating drying method is the most common natural drying, can also be dried at room temperature. However, this method of drying a long time, but also by the impact of a more serious nature. And in epoxy floor paint coating After coating thicker, longer time to dry completely.
    In the natural drying process of the coating should note the following:
    1, the humidity will be on the quality of the dried coating speed and great influence. Under high humidity conditions, may be early field film whitening is also likely to cause the coating stick back, therefore, it is best humidity to less than 75% in a ventilated environment, the film is more prone to dryness but wind speed should not be too large, otherwise it will affect the quality of the coating.
    2, the temperature is too low or too high will affect the quality of a film, it should choose the appropriate weather construction. Light on drying at room temperature is also a great help, ultraviolet light polymerization plays a significant role, but may also result in the film injury, it is important to grasp the degree.
    A good grasp of the coating was dried in entire parking lot due to the need to plan for the parking position, but also install the appropriate protective equipment, and therefore need to provide a variety of different colors, different sizes of parking lot floor paint to make the appropriate planning, has thus increase the difficulty of construction, the construction of the entire parking lot, each part requires careful design and planning, and thus more effective to give some indication of the driver, since the parking lot need to plan a different color, then how do we go design to be able to make better use of the entire car park it? Xiao Bian has the following recommendations.
    1, the parking area for a flat on the ground, can be 0.5mm ordinary epoxy, and poor surface smoothness and strength on the ground, can be used 1-3 mm epoxy mortar floor, epoxy-level requirements can be 2-3mm self-leveling floor; color can be designed into gray.
    2, the companies channel dealers frequently due respect to the parking area, designed to strengthen, may be 1-3 mm epoxy mortar floor or 2-3mm self-leveling epoxy floor, color is usually green, dealers channel width according to scene setting, usually not less than two-way lane 6 meters, one-way carriageway not less than 3 meters, pedestrian passage of 1.5-2 meters on either side draw yellow flag line, width 8-12mm.
    3, inside the garage label channel may be yellow or white sign paint (floor paint can blur night) Draw arrows to indicate the direction and point to individual dealers parking areas, such as parking areas A, B and C parking area parking area, etc. .
    4, parking set up regional structures set up by parking ground parking spaces, cars can be designed generally 2.5-3.0 meters X5-6 meters, parking signs use yellow or white line drawing, standard width 8-12mm.
    5, cylindrical handle to increase the conspicuity parking cylinder to avoid reversing across pillars, 1.0-1.2 meters below the lower end may be yellow and white twill zebra crossing be identified.
    6, vehicle entrance ramp non-slip floor no vibration, vehicle access product must have non-slip effect eliminate noise, parking and some civil construction has been incorporated into the construction of a corrugated uneven ground, just a part of this case channel color coated dealers, part painted another color, two colors and white on it. If design considerations do not slip when the civil claim, on the ground floor construction should be clear here AKF slip floor and non-slip aggregate particle diameter should be larger, typically a diameter of not less than 2mm, depending on the inclination of the ramp and choose a suitable particle diameter non-slip aggregate.
    7, processing dado dado and wall and floor coated with different colors, can play a role in reminding dealers. But not too high, generally 0.2 to 0.7 meters away. With deep green and pale gray and white were signs.

资讯来源：<联系电话:400-0709-910>